167.1 mhz saw filter 1.05 mhz bandwidth part number: SF0167CD02292T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0167CD02292T rev a 15-mar-2010 ecn 36650 page 1 of 3 description ? 167.1 mhz saw bandpass filter with 1.05 mhz bandwidth for cellular application. ? 73 x 20 mm dip package. ? rohs compliant. typical performance horizontal: frequency : 1 mhz/div vertical from top: relative magnitude : 10 db/div relative magnitude : 1 db/div phase linearity : 10 deg rms/div s11 (162.1-172.1 mhz) s22 (162.1-172.1 mhz)
167.1 mhz saw filter 1.05 mhz bandwidth part number: SF0167CD02292T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0167CD02292T rev a 15-mar-2010 ecn 36650 page 2 of 3 specification parameter min typ max units center frequency (fc) 1 - 167.1 - mhz passband width 1.05 1.09 - mhz lower 5 db frequency - 166.49 166.51 mhz upper 5 db frequency 167.69 167.71 - mhz lower 15 db frequency 166.41 166.43 - mhz upper 15 db frequency - 167.77 167.79 mhz insertion loss (at fc) - 18.2 20 db passband amplitude variation 2 - 0.9 1.5 db p-p passband phase ripple 2 - 3 4 deg rms passband phase ripple (over fc+/-0.63 mhz) - 5 6 deg rms group delay ripple 2 - 1.2 1.5 us p-p average group delay (over fc+/-0.63 mhz) 10.375 10.460 10.595 us ultimate rejection 3,4 - 15 - db return loss 2 8 10 - db source and load impedance - 50 - ohms ambient temperature - 25 - c notes: 1. fixed reference frequency. all bandwidths are centered at this frequency. 2. defined over the passband. 3. ultimate rejection is dependent on the pc board. 4. measured across 106.41 to 166. 41 mhz and 167.79 to 227.79 mhz. maximum ratings parameter min typ max units storage temperature range -40 25 85 ? c operating temperature range 0 25 85 ? c input power level - 10 13 dbm matching circuit typical component values: notes: 1. recommend use of 2% tolerance ma tching components. inductor q=45. 2. component values are for reference only and may change depending on board layout. ls1 = 27 nh ls2 = 43 nh cp1 = 53 pf cp2 = 39 pf input 50 ? single-ended output 50 ? single-ended 2 8 all other pins ls1 ls2 cp1 cp2 gnd gnd
167.1 mhz saw filter 1.05 mhz bandwidth part number: SF0167CD02292T spectrum microwave 400 nickerson road, marlbo rough, ma 01752, usa ? phone 1-508-251-6400 ? fax 1-508-251-6401 www.spectrummicrowave.com dsSF0167CD02292T rev a 15-mar-2010 ecn 36650 page 3 of 3 package outline iso 9001 registered all specifications are believed to be accurate and reliable. howe ver, spectrum microwave reserves the right to make changes wit hout notice. ? 2010 all rights reserved. units: mm tolerances are 0.15 mm except where indicated and for the overall length and width, which are nominal values. pin configuration: input: 2 output: 8 ground: all other pins
|
